【单选题】The armed position is the usual position of the switch.
A、武装位置是开关的通常位置。
B、手臂对着的位置是开关的通常位置。
C、该电门通常放置在预位位置。
A、武装位置是开关的通常位置。
B、手臂对着的位置是开关的通常位置。
C、该电门通常放置在预位位置。
【单选题】You can do the test in two different ways -- either with the Central Maintenance Computer System via the MCDU, like you have probably learned already, or with a test switch on the VOR receiver in the avionics compartment.
A、Two controversial ways can be chosen to do the test, either with the Central Maintenance Computer System through a the MCDU, like you have probably learned already, and with a test switch on the VOR receiver in the avionics compartment.
B、You can do the test following procedures -- with the Central Maintenance Computer System by the MCDU, you have probably learned already, and with a test switch on the VOR receiver in the avionics compartment.
C、The test can be done in either way below-- using the Central Maintenance Computer System via the MCDU, as you have probably already learned, or using a test switch on the VOR receiver in the avionics compartment.
A、Two controversial ways can be chosen to do the test, either with the Central Maintenance Computer System through a the MCDU, like you have probably learned already, and with a test switch on the VOR receiver in the avionics compartment.
B、You can do the test following procedures -- with the Central Maintenance Computer System by the MCDU, you have probably learned already, and with a test switch on the VOR receiver in the avionics compartment.
C、The test can be done in either way below-- using the Central Maintenance Computer System via the MCDU, as you have probably already learned, or using a test switch on the VOR receiver in the avionics compartment.
【单选题】Key words or switch and lever positions are capitalized in the Condition Column.
A、关键字、开关及杠杆在“条件栏”大写。
B、大写关键词的开关和杠杆位置。
C、“条件栏”中的关键字或开关及手柄位置使用大写。
A、关键字、开关及杠杆在“条件栏”大写。
B、大写关键词的开关和杠杆位置。
C、“条件栏”中的关键字或开关及手柄位置使用大写。
【单选题】Visually examine the assembly to determine extent of damagE.
A、仔细检查组件来确定是否有进一步的损坏。
B、目视检查组件来确定损坏的部位。
C、目视检查组件来确定损坏的程度。
A、仔细检查组件来确定是否有进一步的损坏。
B、目视检查组件来确定损坏的部位。
C、目视检查组件来确定损坏的程度。
【单选题】Make sure that the indications agree with the position of the flaps.
A、确保那些指示的位置是襟翼的位置。
B、确保指示与襟翼的位置一致。
C、确保那些迹象同意襟翼的位置
A、确保那些指示的位置是襟翼的位置。
B、确保指示与襟翼的位置一致。
C、确保那些迹象同意襟翼的位置
【单选题】The tolerance is plus or minus 0.2 mm.
A、将测量误差值控制在正或负0.2毫米内。
B、误差为正负0.2毫米。
C、标准公差尺寸为正负0.2米。
A、将测量误差值控制在正或负0.2毫米内。
B、误差为正负0.2毫米。
C、标准公差尺寸为正负0.2米。
【单选题】Rate-of-climb of the aircraft will influence the navigation system.
A、飞机爬升会影响导航系统。
B、导航系统受飞机爬升角度的影响。
C、飞机爬升率会影响导航系统。
A、飞机爬升会影响导航系统。
B、导航系统受飞机爬升角度的影响。
C、飞机爬升率会影响导航系统。
【单选题】从法兰上拆下铆钉。
A、Remove the bolts from the flangE.
B、Remove the rivets from the flangE.
C、Remove the rivets from the flanks.
A、Remove the bolts from the flangE.
B、Remove the rivets from the flangE.
C、Remove the rivets from the flanks.
【单选题】当压力降低时,提起盖子。
A、When the pressure decreases, lift the cover.
B、When the pressure increases, lift the cover.
C、When the pressure decreases, lift the covering.
A、When the pressure decreases, lift the cover.
B、When the pressure increases, lift the cover.
C、When the pressure decreases, lift the covering.
【单选题】当门开着时要小心。
A、Be patient while the door is opening.
B、Be aware of the door when it is opening.
C、Be careful while the door is opening.
A、Be patient while the door is opening.
B、Be aware of the door when it is opening.
C、Be careful while the door is opening.
发布评论 查看全部评论